My kospet prime has upgraded V2.0_B this morning， everybody can try it ！
Step：【setting】–> 【about】–> 【firmware upgrade 】
1 Like
We know.
It’s posted above your post.
We have the full flash version as well.
Just in case it is needed
1 Like
I have two questions…
Q1:
I had upgraded firmware from V1.7_B to V2.0B，should I do~ " soft reset "?
Q2 :
What is the difference between V1.7_B and V2.0_B ?
I posted this answer two or three times posts above.
Better language layout for Arabic.
As always they have added bugfixes but we are never told what they are.
I believe one watch face is different as well.
Apart from that - I can’t see any difference.
Battery life is very good but it was before…
Personally I always factory reset but it’s up to you
1 Like
Of course: Prime v2.0 added to the OP.
I edited this G.
To keep firmware in the top post.
Cheers
Pablo11.
3 Likes
Thanks a lot!
Hi,
Just received the Automatic Notification on my Prime for the Update.Downloaded as requested , when it comes to installation s soon as I press the ‘Install Now’ I get a ‘Warning’ re. battery condition as per usual. My battery is currently at 60% also sitting on the Charger Dock, so no problems there. HOWEVER…The Warning Message is static on my screen, so I c
Hi,
Just received the Automatic Notification on my Prime for the Update.Downloaded as requested , when it comes to installation s soon as I press the ‘Install Now’ I get a ‘Warning’ re. battery condition as per usual. My battery is currently at 60% also sitting on the Charger Dock, so no problems there. HOWEVER…The Warning Message is static on my screen, and I cannot clear it ?? so I cannot continue with the Installation ?? Any suggestions please.
Regards Rik
@RIK battery will need to be 75 or 80 % for the message to go away.
You can force reboot and it will either update automatically or you will have to update by pressing update now again
Otherwise just flash the full version added to the OP at the top of this thread.
It is version 2.0_P same as the OTA.
Cheers.
Hi Pablo,
Much appreciated…Watch currently on charge…Once it is at 100% I will give it another try. Thanks for the speedy reply.
Regards,
Rik
1 Like
HI PABLO,
Re previous message. Did as requested. Battery 100% - Download indicates 100% Complete. Hit Install Now, Same Battery Warning Message complete with Cancel Tab - Not Cancelling ??
Tried Rebooting 3 times - still no joy, same outcome ??
Rik
Then I would factory reset and then try.
Have you installed twrp or root tools at all?
I know it’s annoying making a backup, but other people here have taken the update without any problems at all.
Or flash the firmware as I said before.
Cheers
Thanks,
Complete moron when it comes to computers…Jargon is completely over my head…think I will stay as I am as I am happy with the watch and not having any problems
Regards,
Rik
That would be safer and simpler than flashing
Yes, exactly, and this is also how all other devices are upgraded. No installing doubtsome windows drivers which many people have trouble with, or cables which don’t work, etc. Much better user experience.
And luckily they just released the v2.0 as OTA, so I was able to do the easy upgrade. Thanks to the Kospet support team here on the forum 
Fully agree. Actually I haven’t got my Kospet Prime ye, will get in on Monday. I had a Lemfo Lem T which was entirely satisfactory but last week I found it open like an oyster on my desk… Upon examination I found the battery had exploded.
This must be rare though it has happened in the past few years to smartphone of reputable brands.
The delay for getting a new one being too long, I ordered the Kospet Prime which they have in stock where I liven, though I have a definite preference for the rectangular form factor for standard Android Apps…
A good time to buy the Prime as well because I noticed it is discounted at the moment.
You will be happy with it, I’m sure 
1 Like
Hello,
The 1,8 version works very well on my kospet. Is it neccessary to intall the V2.0.
what are the principal change ?.